Welcome TO Our CCIT Communication System

Huawei AP2050DN-S-DC wireless LAN access point 2x2 dual-band, fat and thin support POE power supply

The AP2050DN-S is Huawei's next-generation panel wireless access point for the SMB distribution market. It supports the 802.11ac Wave 2 standard protocol and provides users with high-quality wireless network services.

AP2050DN-S access point
The AP2050DN-S is Huawei's next-generation panel wireless access point for the SMB distribution market. It supports the 802.11ac Wave 2 standard protocol and provides users with high-quality wireless network services. The device's built-in antenna can be used with the 86-type panel cassette to complete the quick installation and deployment; the front is equipped with a sliding panel, which is beautiful and suitable for hotels, apartments, offices and other places.

Key features

Provide one GE uplink and four GE downlinks, and provide two RJ45 telephone ports (compatible with RJ11);
Support panel and desktop installation, easy to deploy;
Provide USB interface, can be used for external power supply, can also be used for storage;
Supports cloud management. Huawei manages and maintains AP devices and services through Huawei cloud management platforms to save network maintenance costs.

Basic parameters

                                                                                                                                                                                                                                                                                             

Project Description
Physical Parameters Size (L x W x H) 140mm×86mm×36mm
weight 0.26kg
Power Parameters Power Input
            
  • DC: 48V±5%
  •         
  • Power over PoE: Meets 802.3af/at Power over Ethernet standards
  •       
Power consumption

11.5W

        

Note: Power consumption varies according to different country and regional regulations.

Environmental Parameters Working temperature 0°C~+40°C
storage temperature -40°C~+70°C
Working humidity 5% to 95% (non-condensing)
Protection Level IP20
Air pressure 53 Kpa~106Kpa
Antenna Type Built-in antenna

WLAN features

Compatible with IEEE 802.11a/b/g/n/ac/ac wave2 standard
The highest rate is 1.267Gbit/s
Supports maximum merger ratio (MRC)
Support for Space Time Block Codes (STBC)
Support beamforming
Supports MU-MIMO
Supports Low Density Parity Check (LDPC)
Supports Maximum Likelihood Decoding (MLD)
Frame aggregation support: A-MPDU (Tx/Rx), A-MSDU (Rx only)
Supports 802.11 Dynamic Frequency Selection (DFS)
Supports ShortGI in 20M, 40M, and 80M modes
Implement priority-based data processing and forwarding based on Wi-Fi Multimedia (WMM) mapping and priority scheduling rules for Wi-Fi multimedia standards
Support both automatic and manual rate adjustment
Support WLAN channel management and channel rate adjustment
(Note: Please refer to "Country Code & Channel Compliance Table" for the specific management channel.)
Support channel automatic scanning function to automatically avoid interference
Supports each SSID in the AP to be independently configured to hide
Supports SST (signal sustain technology)
Support U-APSD power-saving mode
Support for provisioning of wireless access points (CAPWAP) in the Fit AP mode
Support AP automatic online function in Fit AP working mode
Support for Extended Service Set ESS in Fit AP Work Mode
Supports multi-user CAC
Support cloud management

Network characteristics

Meets the IEEE 802.3u standard
Supports auto-negotiation of speed and duplex mode, automatic MDI/MDI-X
Compatible with IEEE 802.1q
Supports VLANs based on user access SSIDs
Uplink Ethernet port supports VLAN trunk function
Support AP uplink management channel network with tag and untag modes
Support DHCP Client, obtain IP address through DHCP
Supports tunnel forwarding and direct forwarding in service data
Supports access isolation between different wireless terminals in the same VLAN
Supports user access control (ACL)
Support LLDP link discovery
Maintain CAPWAP interrupt service in direct forwarding mode in Fit AP mode
AC Unified Authentication Supported in Fit AP Mode
Dual-link AC backup in Fit AP mode
NAT in FAT AP working mode
Support IPv6 in Fit AP Work Mode

QoS features

Implement priority-based data processing and forwarding based on Wi-Fi Multimedia (WMM) mapping and priority scheduling rules for Wi-Fi multimedia standards
Supports RF management of WMM parameters
Support WMM power saving mode
Support uplink packet priority mapping and downlink traffic mapping
Support queue mapping and scheduling
Support per-user bandwidth limit
Support adaptive bandwidth management, automatically adjust user bandwidth allocation according to the number of users, the environment and other factors, improve the user experience
Supports Airtime scheduling

Safety features

Supports Open-System authentication
Supports WEP authentication/encryption, encryption word length supports 64-bit, 128-bit and 152-bit
Supports WPA/WPA2–PSK authentication/encryption methods (WPA/WPA2 Personal Edition)
Supports WPA/WPA2–802.1X authentication/encryption (WPA/WPA2 Enterprise Edition)
Supports WPA-WPA2 hybrid authentication
Support WAPI authentication/encryption
Support WIDS and WIPS, including illegal device detection and counter-attack, attack detection and dynamic blacklist, STA/AP black and white list function
Supports 802.1x authentication, MAC address authentication, and Portal authentication
Supports DHCP Snooping
Support DAI (Dynamic ARP Inspection)
Supports IPSG (IP Source Guard)

Maintenance features

Supports centralized management and maintenance of APs over AC in Fit AP working mode
Fit AP automatic operation in the Fit AP working mode, and automatically load configuration, plug and play
Supports automatic batch upgrades in Fit AP work mode
Support Telnet
Support STelnet, use SSH v2 security protocol
Support SFTP, use SSH v2 security protocol
Support network management real-time monitoring of user configuration information and fast fault location
Support system status alarm
FAT AP operating mode supports web network management AP, can log in via HTTP or HTTPS
Support SNMP v1/v2/v3 in FAT AP working mode
NTP support in FAT AP operating mode

BYOD

Note: BYOD is only supported in Fit AP work mode.
Supports MAC OUI based device type recognition
Supports identification of device types based on HTTP User-Agent information
Supports device type identification based on DHCP Option information
Supports the RADIUS server to forward packets/security/QoS policies based on the types of devices carried in Radius authentication/accounting packets.

positioning service

Note: The location service is only supported in Fit AP mode.
Supports Tag positioning for AeroScout and Ekahau
Supports positioning of WiFi terminals
Collaborate with esight network management to locate illegal devices

Spectrum analysis

Spectral analysis is supported only in the Fit AP operating mode.